stainless steel pipe press fit cap
Stainless steel pipe press fit cap ：High quality inox plumbing sanitary stainless steel 304 316 press fitting .
Shean press fitting system joins pipe without welding or bolting, can be widely used in cold and hot water supply, heating supply, fire protection, medicinal gas, industrial petroleum pipeline system etc. It has already replaced welding fittings in most Europe countries, Asia countries, America, Australia and some other countries.
— Material: Stainless steel 304 and 316 available.
— Max working pressure 1.6MPa (equal to 232 psi),
testing water pressure: 2.5MPa for JIS sizes (equal to 362.5psi), and 5MPa for EN10312 sizes.
— Working temperature from -20 to 110 degree centigrade (with Chlorinated butyl rubber O ring),
— Suit medium: cold water, hot water, compressed air, gas, oil etc
stainless steel pipe press fit cap Standard:
Press fitting standard: GB/T 19228.1-2003, DVGW W534-1995 and JWWA G116
Pipe standard: GB/T 19228.2-2003, BS EN 10312 and JIS G3448
Sealing ring standard: GBT 19228.3-2003, EN681-1:1998
Features of stainless steel pipe press fit cap
By connecting of press fit fittings,the pipeline has high strength,make the connect point “SOLID” at beginning and one time. It does not like threaded pipe fittings,via shocking,threads turns to loose.There is less chances of loosen of couplings in some accident,i.e. Earthquake,house quake,pipeline resonance and hammer vibration. No gas leakage or smoke or fire smoke.
Install by a special small tooling,without welding and threaded,cost and risk are reduced,installation time reduced half,just speed us efficiency.
Compare to threaded 150LB pipe fittings, such fittings should screw turn by turn to be solid fixed, then check if any leakage, if any,shall replace or use Nylon webbing to wrap to test again,until fine enough. compare to butt welded pipe fittings, such fittings should welding between fittings by welding machine along with welding rods,should take lots of time welding from fitting and pipe’s bevel end bottom small angle to upper bigger bevel angle to ensure the welding work strong.
Press fit fitting will insert to straight pipes and press by tool hardly in one time,with O rings inside of fitting,this connect way reduced water or gas leakage,reduced risk of repair and renewal under shade underground environment.
Press fittings has 30 years using life,one time install,long time free of human repair. Greatly reduced cost of products and service fees.
Sealing ring material:
Option 1. CIIR(Chlorinated butyl rubber): Sanitary for human consumption, not oil resistant. Suitable for drinking water, tap water, hot and cold water, sanitary air.
Option 2. EPDM(Ethylene-Propylene-Diene Monomer) : Sanitary for human consumer, not oil resistant. Suitable for drinking water, tap water, hot and cold water, sanitary air and compressed gas.
Option 3: FKM(Fluororubber): It is both oil proof and sanitary. suitable for edible oil, compressed air. But a little more expensive than CIIR, EPDM and NBR.
Sizes range stainless steel pipe press fit cap :
The norminal diameters are: DN15, 20, 25, 32, 40, 50, 65, 80 and DN100, including GB 1 and GB 2.
GB 1 series is same size as EN10312, out diameters are: 18, 22, 28, 35, 42, 54, 76.1, 88.9, 108mm.
GB 2 series is same size as JIS G 3448, out diameters are: 15.88, 22.22, 28.58, 34.00, 42.7, 48.6, 76.1, 88.9, 108mm.
Part of our site:
Installation case example:
* Free sample: we can provide a few free sample for evaluation.
* After-sales service: we provide after-sales technical support for clients.
* Strict Quality control: we have 100% inspection before delivery to ensure every pieces are in good quality.
* 100% replacment if any defects to customers requirements.
Packaging & Shipping
For press fittings packing: we pack press fittings in plastic bag to prevent surface scratch, and then pack them inside brown export cartons.
For pipe packing: we pack the stainless steel pipes inside polybag, so that it can prevent surface scratch, and keep dirts away from the inside of the pipes.
If you have special requirement on packing, please tell us.
We are an ISO certified professional manufaturer supplying stainless steel press fittings and pipes.
We have the following certificates:
SGS witness report;
Please contact us for free sample and pricelist.
Address: Room No.904,Area A of One world business center,
Yun he District ,Cangzhou,Hebei Province,China